HomeElectricityHow Can you Cut Led Strip Lights?

How Can you Cut Led Strip Lights?

Assume you’re designing your ideal gaming space. There’s this one spot where you’re receiving an abnormally large number of LED strips. You might be wondering whether you can cut your LED strip lights.

Yes, LED strip lights can be cut and still function. However, you must ensure that they are trimmed correctly and that the strip’s lights are not damaged.

As previously stated, there is a disadvantage to cutting LED light strips. Otherwise, they will not function properly.

“Now that I’ve got this knowledge, what is the ideal approach for cutting LED light strips?” you might wonder. Below you’ll discover all of the answers you require.

Why You Need to Cust the LED Strip Lights:

Why would somebody cut LED light strips in the first place, one would wonder? After all, if your gaming area has an excessive quantity of LED light strips.

LED Tutorials - RGB LED Strip Light Quick Connectors

If there’s a corner that doesn’t require lighting, it seems sensible to skip the strip entirely.

The truth is that there are instances when you’ll need to trim LED light strips for a variety of reasons.

For instance, you could wish to create a specific form or design. There’s no other option except to cut the LED strips and rejoin the lights (you may also tape them, but we don’t encourage it).

It’s also possible that you’ll only need half of the LED light strip, in which case purchasing a new one is unnecessary.

LED lights may have been put in your room in some situations. Now you’re considering reordering the strips and moving them to other spots.

These are all acceptable reasons why your LED light strips may need to be trimmed.

You should bear in mind that trimming your LED strips is not an issue. They’ll function normally once you’ve completed the procedure.

Tools and Equipment Required for Cutting LED Strip Lights?

To cut LED light strips, you need to have a few tools and equipment at hand.

To make the job easier and more efficient for yourself, we strongly recommend that you use the following:

●   Wirecutter/stripper

●   A Heat Shrinking Tubing

●   Two small pieces of wood/plywood tape

●   Tape measure

●   Soldering iron

●   Exacto knife

How To Cut LED Light Strips The Right Way?

Once you have the needed tools for this job you can start the cutting process. Here’s how to do it without damaging the whole strip of LED lights.

Step 1: Turn off the power.

The very first thing to do when it comes to cutting LED strip lights is to turn off the power. This is the most important step because if you don’t cut off the power then there will be a high chance of a short circuit.

Step 2: Take Proper Measurements

After cutting off the power to the lights, you wouldn’t want to cut the strip without any proper measurements.

It is because if you cut without taking all the measurements then there is a higher possibility that the result will look ugly.

Therefore, you need to take proper measurements using a measuring tape and a pencil or a marker.

Step 3: Making the Cut

From the welding point part of the dotted line in the figure below, notice that the scissors and the light strip surface are perpendicular (90°) to each other.  (Eugen, 2021)

This is the most important step and should always be carried out with extreme care. Cutting in itself is a very simple thing. Just make sure you cut at the right angle without damaging any LEDs. The main thing is if you are careless, chances are you will damage your whole LED strip.

Always make sure to keep the cutter slightly away from the LED to prevent any damage. The cut must be as straight as possible otherwise it will look horrible on corners.

Step 4: Rejoining The Strip Pieces/Soldering

Once you cut your led light strip the next thing most people would want to do is to join the two pieces together. This part is mostly for corners so you should do it with care.

During the joining process, there are two ways to join the strips. One of the methods is to solder the two strips together using the pins on LED light strips. However, this requires knowledge related to electronic circuits otherwise your lights won’t work.

Led strip lights come in a variety of configurations including 2, 3, 4, and 6-point/pin connection strips.

You can join these strips using either a connector or by soldering the points.

The easy way is to use a connection clip as it is pre-configured and doesn’t require any soldering which saves time.

However, if the clip is not available then soldering can be handy in such situations.

The next and probably the safer way is by using pre-made joining clips. These are available at different electronic stores and the best thing is they are ready for connection without any kind of soldering. (Geek Street, 2021)

Below is a specific connection method of connector connection and welding.

However, you will need to make sure that your strip and the clip have the same number of connection pins.

For more details, you can watch and follow the guidelines as described in the video.

Step 5: Secure the Joint with a Shrinking Tube

Once you have connected the two pieces, the next thing is to test them. You need to put them on an insulator body and turn on the switch and see if they work. Once you have confirmed their working, the next thing is to secure the join using a shrinking tube.

This step is very easy and all you need to do is slide the strip inside the tube and place it right on top of the junction. Once the tube is in place, use a heat gun or a hairdryer to shrink the tube.

Using a shrinking tube is very important because it protects the connection and will help prolong its lifespan.

Information Related to the Topic How Can you Cut Led Strip Lights

Here are the search results of the thread How Can you Cut Led Strip Lights from Bing. You can read more if you want.

You have just come across an article on the topic How Can you Cut Led Strip Lights. If you found this article useful, please share it. Thank you very much.


Elon Williams
Elon Williamshttps://triplegems.org
Elon is a freelance game writer for GamersMania and Edge Magazine, who also works in game design consultation and localization. As a British Person, he enjoys Hollywood movies and 3D games and is always on the hunt for the next game from the Land of the Rising Sun.


Please enter your comment!
Please enter your name here


Popular posts

My favorites

I'm social